Search results

Just recently my drivers door has gotten sloppy. Tougher to close and getting more wind noise than ever. Looks like options are limited to SKP and Dorman across all big box stores and RA. Looks like there are 2 different types: Has anyone had experience with either? Is the thread on superior...

I am trying to get to the bottom of an on-going issue I've had for several years with my 05 Yukon XL. It is mostly pertaining to power steering effort while the vehicle is moving very slow or stationary. Specifically navigating parking spaces, parallel parking, at idle, etc. I have very little...

My 05 Yukon was experiencing water intrusion about a year or two ago. Specifically in the cargo area from the vents in the D-pillars as well as the electrical penetrations for the rear lift gate. I utilized a Home Depot exterior grade clear silicone sealant which seemed to work well for a year...

Not entirely sure whats wrong yet, but it doesn't look right. Look at how the new pad sits in in the mount on each side of the rotor. Notice a big difference? If you can't tell via pad and mount, look at where the rotor rides in the opening of the bracket! Its not centered even woth the...

Anyone have any experience with eBay or Amazon aftermarket replacement heated seat elements? How about the Seat Shop? My drivers seat in the 05 Yukon will trip out almost immediately. It has a dual button (back only, or back and butt). No matter the selection it trips off leading me to think the...

As the title states, 1 winter with my new to me black 20's and the clear coat has peeled rapidly. Wondering what i can do to stop it. Obviously not looking to completely refinish the wheel, but open to other lower cost options. Thinking about peeling the delamination off and coating just that...

All, Back story: I just splurged some coin to get my A/C back in operation on the Yukon. When I got it someone had several of the lines disconnected under the hood for reasons I don't know. I took it over to a buddy mechanic to try and get it working again. After replacement of 2 lines he had...

Welp I ended up stumbling on this 2005 Yukon XL in SLT trim for peanuts off a young kid who used it for his transport business. With the rising duel costs he was selling to purchase a smaller van. I jumped quickly into action to get this thing ready for my trip to TN. The day I picked it up and...

Yep, another iron in the fire. We have been avid campers for the past 2 years now at a local site about 15 minutes from our house. Several other family members have carts up there from stock (89 EZ Go Marathon) to not (02 Club Car 670 swapped). We have so many people at camp that we really...

I think I had a few photos posted of this unit somewhere in my one-size-fits all threat but we are taking the next step. Background is my family purchased a club car from a golf course for our seasonal campsite. First was the rear seat install, then came the HD rear springs, then the 6" lift...

This project is going to be a tad different than the norm here. With my oldest about to turn 3 in August I decided to get him a power wheels, with intentions to modify it after he gets the hang of it. I set my eyes on a used unit as It will be tough to hack up a new $400 unit. I never had these...

All, I have gotten back into the swing of working on my truck (69 1300D SRW) alone on the weekends back at the place of employment. I pulled my rear drum/hub units to inspect/repack the wheel bearings and replace the seals. Upon removal of the driver inner bearing I noticed a substantial amount...

As some of you have seen before this rig and know I have had my eyes on it. The truck is an old IH fire truck. Some back story is the truck: It was utilized on an Alcoa Foundry. I'm assuming all its life as the odometer seems legit with 4,600 miles. Reasoning for legitness is pedals are in great...

So a few months ago I had to take my Boss's truck to the local Chevy dealer for service. On the way over I noticed that there was a substantial amount of play in the steering wheel (reminded me of my old 94' Silverado Plow Truck it was that bad). Id say there is a solid inch of play and when the...

Good Morning Guys, Our trusty 2004 3500 Dually got towed to our shop yesterday. Driver stated RPM's were rising on a highway drive to the jobsite. We checked the truck when it came in and the fluid was way over full. Supposedly the driver added some transmission additive in an attempt to fix...

Long story short I had my '94 Lightning Roller Block bored 0.030 over and had flat tops installed about 1.5 years ago. Builder and I split ways on rough terms after several missed deadlines and blowing off meetings. Got the engine back supposedly finished, however valve train setup was horrid...

Hey guys, Looking for some input here as to what PSI i should run in my new Kumho KL-78's on my F250. Currently I'm pissing off the TPMS (They call for 65 PSI) and I' currently running 50 PSI. My rims are the 20'' diameter (8'' wide) 8-spoke Lariat/King Ranch rims with 325/75/R20's on them...

Hello all, Figured i would start a build thread on my new truck. Been to a few other forums since I've owned my 6.5 and none of them feel as welcoming as TTS. Since my 6.5 days I've finally graduated (for the last time) and now am an estimator/project coordinator at a demolition company. I...

Hello Everyone, Been a few years since I've been active on the forum since selling the 6.5. Dabbled in the gasser half ton pickup market for 2 years and am looking to get back into a diesel. Been looking heavily into the 6.0L rig. I know everyone is going to try and steer me away but I've had...

Hello all, I have had an issue for a year or two now with something in my heater box. The issue has come and gone about 2-3 times and is back again. When I start the truck something in the box makes a "flapping" sound. This sound will go on for 20-30 seconds and then stop. But if I hit the...