Search results

so on my fuse pannel their is a fuse that has been blown since i got the truck and never really bothered me but im just wondering what is the SOL circit for. i looked in the ownes mannual and it has all the others but not that one. can some one tell me what it controls or dose

i am looking for a 3500 crew or extended cab with the 6.5. i want to get a DRW model. not to pickie on 4 or 2 wheel drive(would prefer 4x4) also not a big deal about the trans.

ok so had to replace my cluch master cylnder and did and also the slave figure good time to do it. well i got them all in got a new hydro line to go from one to the other got all installed no real problem. here is the problem went to go bleed the system and after about an hour and a half i have...

ok guys i did the dumbest thing ever opened my hood to see a part i needed at the auto parts store closed the hood but did not latch it go in store get parts forget to latch hood start driving and next thing you know i cant see because of a hood. so i am now looking to get a ram air or a cowl...

if anybody has ever raced a 6.5 they are kind of slugish down the 1/4 well im going to change that. im planning on building up my 6.5 to go fast. i know it will take some doing but i think i have a good start seeing as im already a 1000 lbs lighter then al the other trucks. ive been told im...

Any body out their goinging to TS this year sonunds like a good time. I will be their putting the truck down the strip a couple of times.

So i recently took all the rubber trim and stops off my front bumper and filled in the holes. Now i would like to clean it up a bit more before i paint it and some of the welds when i filled in the holes had porocity and others i may have ground down a little to much. Now the question what do i...

:???:so I believe that I have the syncro going out in 2nd gear. I was told that it was probably that because it sounds like its grinding the gear no matter how gentle I put it in gear. now I found a kit with all the new parts minus big parts(gears, shafts) it in for a decent price. I'm just...

well i got new seats put in my truck. they were from an 07 ram 2500. so with a little fab work and and some broken skin later i have 2 bucket seats and a big hole in bettween were i will evntualy put my center console. will post pictues of the job as as it gets further alon(mostly the center...

Ok i recently instsalled an HX35 turbo on my truck and i think i may have an issue that is i can only get 15 pounds of boost out of it. Now i know from others with this kind of turbo the can get up to 30 to 35 pounds so why will mine only make 15.

pullin injector cups in buddys truck how do we drain the block of coolant so we can change them it is an 01 6.6

I got an isspro fuel pressure gauge and airdog 165, well the gauge didn't come with the piece for the fuel line and the lift pump didn't have a place for the gauge sensor to go. so what is technical name for this piece or the place to get it. I hope I gave enough info

Im getting ready to put in an airdog system and want to put in a system like a "feed the beast" kit so I was just wondering what the thread pitch is for the fitting going into the pump so I can get the fittings before I put in the airdog system

ok I want to do some pulling events and just wondering about what I can do with set up my truck when ever I get to an event and what kind of hook up should I use. now my truck dose not have a hitch and has an after market bumper that says its can have a pinle hook for 12000 pounds so can I mount...

so on a few other places I have seen the 4x4 decals that have 6.5td under it. I was just wondering if any body knew were to find them at or am I going to have to get them custom made

im changing the coolant on my truck and am just wondering how you get the coolant out of the motor

So my buddy has an 01 lb7 duramax. he got the truck and was leaking everything every were. well he recently replaced the injectors, push rods, put in head studs. when he got it all back together he changed the oil in it. we went to start it up last night and after we got it started he went to...

Ok so im pretty sure i have a good bit of blow by. I can tell because it is coming out of the dip stick, the oil filler neck and the tuna can. so why a i getting blow by so bad

ok so i know that tha vacuum pump was mostly for the waste gate on my stock turbo but what eles is it for. seeing as i dont have a stock turbo anymore i was just wondering if i still need it and if i dont can i get a delete kit for it

What kind of pressure can the injection pump take.im trying to start to feed it and was just wondering