Search results

From what I recall when going to 4 wheel disc you had to switch to a 4 wheel disc brake master cylinder and proportional valve which I believe the easiest swap is the 3500 HD master cylinder and the HD proportional valve. I was not sure of the hydro boost, I will be installing a 2001 14 bolt...

Hey guys, I was just starting to work on my front brake conversion but I'm not quite ready to swap the rear axle to a disc brake 14 bolt unit. My problem is my hydro boost just started leaking so it needs to be replaced. My question is I know when swapping to rear disc brakes I need to swap in a...

The steel one that goes on the front side of the compressor, not the cast one behind it .It has two bolt holes that bolt onto two water pump bolt studs.

Admin please delete this post.

I'm looking for the front Ac compressor/ vacuum pump bracket if anyone has one LMK, Thx

LIKE THE TITLE SAYS THIS IS A GM C/K SERIES TRUCK 8 WAY POWER FRONT DRIVERS SEAT BASE FOR 1995-2000 GMT400 BODY TRUCKS & SUV's $200 PLUS THE RIDE. THEY ARE OVER $300 ON EBAY. HARD TO FIND ONE THAT EVERYTHING WORKS LIKE THIS ONE.

Hey SnowDrift, do you want this filter?

The filter that is on it looks like a Car Quest 86755

Yes that part of the harness connects to the backside of the IP.

THIS IS A 3.5 INCH EXHAUST SYSTEM FROM A 6.5 DIESEL SUBURBAN, HANGERS WERE UNBOLTED FROM FRAME AND ARE STILL ATTACHED. SHOULD FIT MOST TRUCKS WITH A 6.5 ENGINE. I DON'T THINK I CAN BOX THIS UP SO IT'S LOCAL PICKUP IN FT PIERCE FLORIDA. $100.00

CAN ANYONE USE THIS PREFILTER WITH PRIMER PUMP? COMES WITH MOUTING HARDWARE $40.00 PLUS SHIPPING

THIS IS A FSD COOLER AND FSD FROM PENSACOLA DIESEL, ENGINE RAN WHEN UNIT WAS PULLED. FYI THE HARNESS EXTENSION IS HOME MADE WITH WIRE AND BUT CONNECTORS WITH HEAT SHRINK. IT COMES WITH A BRACKET THAT BOLTED IT TO THE BOTTOM OF THE FRONT BUMPER, (SEE PHOTO) I FIGURE IT'S WORTH $100.00 PLUS SHIPPING

ADMINS PLEASE DELETE THIS POST OR TELL ME HOW TO DO IT PLS.

Does anyone know at what temp does the Duramax fan clutch kicks in? I would have to dig through this thread or my loads of receipts for when I bought my fan for a part number but I can't get my engine to run over 190* period, even with the grill totally covered with card board. I think it's...

What are the stock "REAL" Marine Injectors with 311 nozzles set to pop at? Anyone know?

My local diesel shop says he can get one next week for $50.00 but dang! I'll buy 9 of them if I could find them for a decent price.

Thanks Will, I'm striking out on finding any. I found what looks like Chinese knock off's but that's about it. I bought the last set of Bosch ones on ebay years ago but the ebay ones all say sold out.

I'm looking to buy some 311 injector nozzles, the last set I bought on ebay but I can't seem to be able to find genuine Bosch nozzles. I don't have the Bosch part number so if anyone has that it may help. Any help is greatly appreciated.

So just to update on this issue, so I installed the heat shield blanket and it didn't change the no start when hot issue. I then was able to find the little bracket that holds the factory heat shield to the bell housing bolt. So I then dropped the starter and installed the OEM solenoid that Nate...

SO LIKE THE TITLE SAYS, WHAT'S THE BEST STAND ALONE TRANSMISSION CONTROLLER FOR A DS4 TO DB2 INJECTION PUMP CONVERSION USEING A 4L80E TRANS?