Search results

The eventual plan for this truck is to pull the 6.5 na crate motor out of my 93 and put in here and sell this 6.2, MN winters rotted the frame on the 93 but that engine is in excellent condition, just not ready to do it yet. So if I can get a year or 2 out of this that's all I need. Thanks for...

Little update, I added a gallon of atf and a overdose of howes to 1/4 tank of fuel, keep in mind a 36 gallon tank so still decent amount of fuel. Let it idle 45 min before 20 mile round trip for lunch. Drove it decent at first then got more aggressive with it, usually drive pretty nice. Didn't...

I dumped a stiff dose of dextron 3 in it and I'll drive it on my lunch break. The return line is 1/4" iirc?

Haven't put a clear line on the return yet, not ruling it out or anything but when my 83 had air getting in it started like shit, this thing fires right up and runs smooth, but I'll get a clear line on it. Never been able to get it to do it unless under a load/acceleration not sitting still...

Been way too long since I've been on here, my 1993 was just way too reliable I never needed to monkey with it, finally retired it do to rust. Bought a 1991 2500 6.2 J code. Issue started a few months back when accelerating between 2,000 and 2,500 rpm it kinda cuts out or almost like a misfire...

IIRC removing the OS filter on OBD1 (94-95) trucks is not recommended. It's been found to not be necessary on 96 and up OBD2 trucks. Someone can correct me if I'm wrong.

My '83 had the drains mounted on the frame right behind the fuel tanks believe it's supposed to be a water drain for the tank, never opened mine and due to Minnesota winters they probably won't budge. As far as the return lines on the injectors if they are the braided style they do not need...

Agree with Just a number most likely the front crank seal oil getting flung around by the fan. Clean it up with brake clean, start it up and watch for drips.

Gotten lucky before with just a oil pump. Yea it's a pain but better than scraping the motor or the whole truck.

That's what I was afraid of! I guess i bought it cheap enough another $100 onto it won't be so bad. I guess I will be contacting bully dog tomorrow. Thanks for the help guys!

Bought a used bully dog GT. Previous owner did not return it to stock when he removed it. He now installed a H&S tuner. If i hook the bully dog back to his truck and return to stock will it still work or does the H&S write over all the bully dog data? Bully Dog can unlock it for $100 if need be...

I usually tighten the P.S. from underneath the truck... IIRC there is a spot in the bracket for a 1/2" drive ratchet... or use a pry bar BUT BE CAREFULL where you pry! I've seen someone poke a hole in the resivor before

That would be the reason my Duramax sits in the garage most of the winter!! Lol If it doess get drove in the salt it gets sprayed off for sure! Which is what started all this had to get the old reliable 6.2 all fixed up for winter

Pepperidge... that is my next purchase some big flares that will cover all that uglyness up! As far as the rust goes I just had a 1996 chevy in the shop this week that was worse! Makes the 5th truck I've seen with the frame rotted in the same spot... seen a 88, 91, my 93, a 94 and now 96. This...

I've got some before and after of the truck and the rims, i will take some this weekend of my filter setup... 1st pic rims when i got them. 2nd is after I got done sanding and polishing. 3rd rims on the truck with LT285/75/16 Trailcutter R/T's on them. 4th is my true dual exhaust setup. 5th the...

Like the title says i haven't been on in awhile, way too long in fact! So i thought i would log on and update some changes I've made on the old 6.2. First off to start the whole project i needed tires had no driving or steering complaints other then funny tire wear... but boy did I have issues...

www.mouser.com, mouser's part number is 829-15356826. The original delphi part number is 15356826. HERE is the link

It was mouser electronics i think. Im at work right now when i get home tonight i'll post the site and the part number. They were 36 cents a piece, cost more to ship then that!

Just a update I did find the pin's using a delphi part number. My local dealer couldn't find them but i found a place online that sells them. Got it all hooked up, works awesome. Biggest challenge was finding a place to get through the firewall, but all in all it took about a hour to do it.

That would be great guys! Thanks for the help