Search results

Man you guys are awesome, I appreciate the help and the detailed replies

Hey all, I've gone and bought a replacement for my LBZ because the trans was giving me issues and computers aren't my thing... So I bought a 12 valve. I've been getting used to the learning curve of the 5 speed manual plus a low redline, and I had a question. In third gear, (which seems to...

Right now it is straight-piped downpipe back with no codes. I'm considering an EGR blocker plate also.

Today I went through all my RPO codes on my glovebox just for fun. I found out that my truck is FE9 federal emissions, not California. :coolgleamA: Does this mean anything special? Can I just rip all the emissions stuff off my engine? (Kidding). But do I need to keep my mouth shut because it is...

They are the originals from when I bought the truck last year, mismatched, one autozone and one walmart haha. I'd like to get two interstates, but they've worked so far. I took your advice this morning, and after it did its little routine i tightened up the positive lead from the driver side...

Hey all, I'm back with more issues with the 07 Duramax. I've been noticing it has been resetting the clock in the factory radio, but it hasn't messed with the radio presets. Now, this didn't bother me until last night when I tried to start it and just got a slow clicking noise, a little bit...

Hey all, I've been looking at this Duramileage tuner that has had some controversial reviews and I think I'm going to try it. I get about 13.5 MPG in my LBZ and I don't drive like a grandma at all... But I think I will try the handheld that they are selling now and see if I get any...

Hey guys, I was wondering if anyone knew if you have to run a banks tuner to use the iQ gauge system. I saw it installed in a Dodge and I liked the versatility, but I don't need the Six-Gun or whatever it is. Thanks

So You think I should get a dry filter in the S&B instead of the cotton one? Why is that?

It has 179,000 miles on it. And I'm glad to know I've been doing the right thing, because I changed the fuel filter and have been running the silver power service stuff. Does someone have to be a specialist in EFI live to program the truck? And I think I'm going to do the Banks airbox anyway if...

Hey all, I bought a new truck, unmodified, and drove it all the way home from Texas, to find it needed the whole front end rebuilt, shocks, the cruise control doesn't work and it smokes like crazy, especially for being stock. :mad2: After replacing a clogged air filter, it got a little tiny bit...

That would make sense, but I don't think I unplugged a barometric sensor... I could trace where the wire loom went over the old turbo horn into the same sensor. Now I have a code for the boost sensor, obviously because it's unplugged. However, the MAP code is gone.

The one I have unplugged is on top of the intake, right next to the intake heater, It has a little hose that runs down to a tiny hole in the pipe, right before the pipe bolts to the intake bridge. I believe it's the boost sensor. (I've been hearing all kinds of different names for this thing)...

Yes, after unplugging the sensor and clearing the codes it runs just fine. Is there a problem with running it without the map sensor plugged in?

So today I fired the truck up again and I had a check engine light. Plugged it in to the scanner and I got two P0107's and two P1639's. After untwist/untaping the three wires and securely soldering them together, still no change. I cleared the codes and tried again, still no throttle response...

Hello guys I'm back again, I just spent a few hours installing a Profab turbo horn on my '02 LB7, and having connected everything back the way it was (almost), I found the boost/MAP sensor connector was too short to make it back to the sensor. :mad2: So after a run to the parts store I got a...

Thank you sir! Now the fun part... haha

Hey all, I recently bought a set of glowshift gauges for my 02 LB7 and I'm trying to install them. I cannot find the FRP sensor to save my life, and nobody else seems to know where the heck it is! :WTF: PPE has an "optional" harness to install their gauge, but still they don't show how to hook...

Anyone dealt with Cooper ST's? Not the Maxx, the original. They're going away now but I found a set i was thinking on buying to replace some worn out Transforce A/T's. Looking at 265/75-R16's.

Alright, I'm going to put a gauge pod on the pillar I think, so it'll all work out. But he wants 200, I might just wait and get that PPE Economy one. Thanks for the advice.