I did the window screen just like you did several years ago. I was able to find black metal screen so it blends in a little better.
Just like you I spent a day cleaning the radiator/coolers and AC. After that fun filled day I said no more and installed a screen. They only thing I can tell...
On my Kennedy LP harness it uses it's own OPS for power when running, this OPS works as a on/off switch when oil pressure is present. If you unplug the harness from this second OPS the system should default "LP ON" when the ignition is under power.
One time I washed my engine and the second...
Thanks for the info. At some point I plan to move the gauge to the output of the FFM. Currently I need the new lift pump and plan on heading out of town for work.
Brian
Greetings,
My Walbro FRC-10 died after about 1-1.5 years of good service. Not wanting to have the same issue one year later I have purchased a Raptor 100 kit from Leroy.
What pressure should I set? The truck has a fuel pressure gauge pre-FFM and is monitored in cab. According to my...
Holy Crap Batman! Get a tetanus shot before attempting repair! :hihi:
I think this was your glow plug, perhaps someone else can zoom in and confirm. It looks like getting that thing out will not be easy. As others have said soak this thing in some type of solution to help break up the...
When I had a P400 put in my 95 suburban, Peninsular cut and welded the cast pan so it would fit in a non lifted 4X4 vehicle. They did a fantastic job. I think they said they had a jig to do it with.
Good luck with the install! The P400 is a very nice motor!
Brian
The diesel burbs got 8 lug wheels (I think it started in 94 thru 99), even the half-ton diesel versions. You should also have an "F" engine. So it is a 1500 with a frame that is closer to a 3/4 ton. You probably have 3.42 axle. They were only offered with the 1/2 ton.
Really the difference...
Use artic silver and you will be fine. If you need it now you can buy it at Radio Shack. I have used it for the PMD with no problems, just make sure your heat sink is clean. A little goes a long way.
Good stuff
Brian
I used this stuff http://www.homedepot.com/buy/appliances/air-conditioners-fans-dehumidifiers/ac-safe/foam-coil-cleaner-22963.html
It really helped clear the bugs and dirt, I used a lot if it and rinsed the system with water, over and over. I also used a pick to help dig out the little rocks...
Ok to try to finish this up, after changing the first fuel filter I still had air in the system. I rechecked the fuel system pre lift pump with no luck, still air bubbles. I attached another clear line from the IP to the fuel return system. No bubbles coming from the IP so my problem had to...
So here is what I know from tonight's journey of understanding of the 6.5 turbo diesel.
I installed the clear hose on the fuel return and surprise surprise, bubbles of air. Not a few but a bunch. So I started under the burb where I installed a Racor fuel filter/heater. All hose connections...
I will check for air tomorrow, the fuel system is fully modified. The FFM filter was changed 2000 miles ago but I will look into it. After the FFM I have the feed the beast mod. I also have a Racor filter pre-lift pump and it's filter was changed 2000 miles ago. I guess if a fuel connector...
I am running a Walbro FRB-5. I have a pressure gauge after the lift pump, before the factory fuel filter and the lowest pressure I have witnessed is 5 psi. It normally runs 7 - 8 psi cruising down the road. Is this pressure OK?
Thanks
Brian
While driving around this afternoon it was warm 95 deg I noticed my idle was higher than usual. I have had this problem before and thought nothing of it. Today I decided to look further.
Reading the active codes I have a 98 Cylinder balance Fault #8 and 94 Cylinder balance fault #5. In...