Indeed - England in the UK!
the calipers seem to move freely ok - the pins are well lubed
is there a way to suspend the ABS system? I removed the brake fuse which caused the car to go into limp mode
thanks
Hi there,
I recently changed front brake pads on my chevy, bled the sys incl ABS, but the brake pistions would not retract
and stay in brake mode which causes overheating and disintegration of the pads,
what causes the pistions not to retract?
thanks
Thank you all guys - all good now, th big chevy has started fine,
we shorted the shut off selenoid with the battery and also disconnected and reconnected both batteries.
I recently changed the fuel f - visually it is looking ok,
are the other items seviceable?
How about if I disconnect both batteries to reset the ECU - would that cause any other issues?
Hi all,
Today - all of the sudden my 1995 chevy 6.5TD sub K1500 4x4 (mechanical IP) wont start for love of for money,
it started fine first thing in the morning, drove ok for most of the day then refused to start later in the day.
the only thing that changed recently is the fuel - where...
Hi all,
My chevy now permanently cold, I checked the one thermo on top of the engine it appear to be bad, it wont close,
is there more than one thermostat? to change it are there any seals I need to change at the same time?
Many thanks
Please help,
This is the first time I am trying to change front brake pads on a 1994 chevy sub 4x4 K1500 auto,
I ordered pads part no SMD369 using the VIN number but they don't fit as well as the old ones (see att pic)
1. the two prongs on the inner pad are slightly wider for the caliper -...
Hi,
my 1994 chevy sub 4x4 4L60E tranny is leaking fluid from the cooler pipe just where it
goes into the tranny - it is the bottom one - not sure if it is the out or the return.
I have attempted to tight it but still leaks.
also - tranny oil is low, where do I find the fluid addition...
Hi there,
Lately - my 1994 K1500 chevy 6.5TD and 4L60E auto tranny (4x4) was getting very noisy from the back of the engine area,
when we took inspection cover out we found the flexplate was broken around the bolts (three of them) that hold it to the TC,
1. any easy way to replace the...
Thanks guys,
I 've also been told that there are bolts that hold the starter ring gear that might be loose? do you guys know about these bolts?
I am trying to remove the inspection plate over the big wheel that connects to the starter motor but the exhaust pipe is in the way
removing it is...
Hi,
1994 chevy sub K1500 4x4 Auto 4L80E 6.5TD (engine was 5.7L gas)
Recently and after a long drive I noticed my car had developed a lots of noise from under the engine/transfer case,
Looking at it with the engine running idle I noticed the Starter Ring Gear wobbles badly,
also it always...
Hi,
Since I bought my 4x4 chevy the auto tranny shift indicator (mechanical slider type) never worked as the cable attach to it is not connected at the other end,
can someone please advise where should I attach it to? and how?
also the vehicle come with P255/70R16 111T tires, what should...
Deejaa, thats what I concluded from all the advice kindly given here by the good people on this Forum,
I am taking the vehicle to a reputable axle guy who should do it.
Thanks Missy, so you suggest it's best to rebuild what I have?
for a typical job like this what should I order? is there a set kit that can be ordered?
It is dificult getting hold of workshop manual here in the UK, do you know of a good downloadable version somewhere?
Greetings from a dark cold...
Right guys - I am slowly getting up to speed on all of these thanks to you:
1. just to recap the vehicle is a 1994 burban K1500 4x4 with 5stud wheels, 10bolt axle and 3.73 gear ratio
VIN1: 1GNFK16K3RJ424774 (this vehicle which was gaser 5.7L)
VIN2: 1GTHK33F5TF009115 (donor motor: 6.5TD...