Search results

I'm looking to buy another truck. If I"m looking at one of these trucks what should I pay attention to? Other than the standard body, frame, suspension issues. Thanks.

I'm looking to buy another truck. If I"m looking at one of these trucks what should I pay attention to? Other than the standard body, frame, suspension issues. Thanks.

I'm looking to buy another truck. If I"m looking at one of these trucks what should I pay attention to? Other than the standard body, frame, suspension issues. Thanks.

Had the fasteners that hold the flange of the y pipe to the flange of the exhaust system fail. Does anyone know if these are bolts or studs? 4 fasteners through flanges and square gasket

Truck ran fine last night. Shut off 4 hrs from home when I went into truck stop. Restarted and truck ran long enough to back out of parking space. Would crank, halfway fire then nothing. Have about 1/2 tank of fuel. Fuel to filter manager. Fuel to injectors. Pmd was remote mounted. Pulled it...

Is it righty tighty lefty loosey or lefty tighty righty loosey?

How in the (*(*& do you manage to break on of the wings the distributor cap screws to off of the distributor? Was replacing plugs, wires, cap, and rotor on a truck with a 7.4 Vortec I just got. One of the bolts holding the coil bracket on was missing the other had the head mostly ground off, so...

Is it possible to run 265/75-16 on a stock height 97 C2500?

For the past several years I haven't had time to sleep much less turn a wrench. Now I've got a little time and my Snap-On Brick has died. Need a scanner that will work on 96 and up GM, Ford and Toyota. When I was active Autoenginuity was the top dog for PC based scan tools. Looked today and...

Got one or more of the following bad head gasket cracked head cracked block This means I've got to pull the heads. When I speced the build for the motor years ago ARP studs were used. IIRC the procedure with studs on the passenger side it is remove the nuts from all of the studs and...

Have a new filter manager. Great if you are looking to do a feed the beast mod. No WIF or fuel heater. $50 obo + shipping

Been awhile since I've been on. Enforced 6/10s hasn't left much time to hang out on forums. Took a pay hit to get another position that will have better hours and be better on my body. Drivers door hasn't fit right since I've had the truck, drivers rocker is going, and rusting out at the bottom...

Would you go with the 35w or the 55w kit?

Going in to work this morning, stepped on pedal and nothing. Truck idling fine but no throttle response. Dash light shows service throttle soon code shows p0251

Turn the key and no crank. New batteries grounds clean. Accessories turn on. Can hear glow plug solenoid and lift pump. Starter doesn't attempt to move.

My brother didn't have a good day yesterday. He managed to bust the gearbox on our 3pt hitch tiller. Then while hauling another tractor, managed to break the transmission in my truck., He was going down the interstate it popped out of gear. I haven't had a chance to check it out but...

Can someone get me some rough dimensions of the front clip on our trucks? From point on fender closest to the rear to the furthest point in the front of the hood and a close guestimate across the front. Got in a fender bender and need to replace the front clip. Need to see if the replacement...

Get your minds out of the gutter. I'M TALKING ABOUT THE TRUCK. How do ya'll in the regions that get lots of snow and ice deal with the build up in the rear fenders? Had an iceberg on both sides that filled the fender well and was rubbing on the tires and setting on the tail pipe.

Who has a tool box mounted in that wasted space between the deck and the hitch on their trailer? I'd like to install one to store tie downs, binders, bars for the weight distribution hitch, etc. I'm tired of chasing down stuff that should be stored with the trailer. Everything I've seen...

Any suggestions on where to buy replacement trailer tires. I'm going to need some ST225-75R15 LR E's. Brother was pulling my trailer with a 68 Torino GT he'd picked up and had all the tread decide to leave one of the tires without the tire going flat. Currently have the Carlisle's that...