n8in8or
I never met a project I didn’t like
Probably so.Yup, but for us with stock type of AF system that could create an even larger source of outside air directly into the AF snorkel.
I think ? ? ? ?
-
Welcome to The Truck Stop! We see you haven't REGISTERED yet.
Your truck knowledge is missing!
- Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
- We have tons of knowledge here for your diesel truck!
- Post your own topics and reply to existing threads to help others out!
- NO ADS! The site is fully functional and ad free!
Problems registering? Click here to contact us!
Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!
1994 K3500 extended cab dually
- Thread starter n8in8or
- Start date
MrMarty51
Well-Known Member
I believe thats a grand idea so I’m thinking of copying what You did there.
I found a set of these.
But I’m going to do some measuring afore I order them.
I too had been looking at hood scoops but did not want a bunch of water pouring in, or snow. Your plan with the fender skirts is an excellent alternative.
Thank You very much for posting improvements such as these fender vents.
n8in8or
I never met a project I didn’t like
Downpipe is painted and wrapped.
And now installed.
So once again, the exhaust is done, for real this time…….except for the tip, which I will do after the bed is installed.
And now installed.
So once again, the exhaust is done, for real this time…….except for the tip, which I will do after the bed is installed.
So you checked the Inter fender fit?
n8in8or
I never met a project I didn’t like
DieselSlug
Well-Known Member
Very clean. I wrapped mine on the '94, unfortunately being my plow truck it vastly expedited the rot and I ended up replacing the downpipe barely 2 winters after.
n8in8or
I never met a project I didn’t like
Yeah, that’s why I didn’t want to wrap the headers, but since this is stainless, I’m hoping it will hold up.
dbrannon79
I'm getting there!
All these new vehicles out there, it be nice if they made repop parts and maybe even frames from stainless!
Will L.
Well-Known Member
$$$$$$
n8in8or
I never met a project I didn’t like
I took some time off for a trip, but got back at it today. I was thinking some more about how to make the hole and how to fasten the scoop to the fender and came up with what I think is a better idea: rather than make a trim ring that sandwiched the scoop to the fender, I decided to make a more finished opening and adhere the scoop to the inside of the fender with 2-sided VHB tape.
First step was making a ring for the opening out of 3/16” steel rod.
Once the ring was complete, I used that as a template for marking the opening in the fender and then cut it out and trimmed it.
Lots of MIG tacks and grinding and it was welded to the fender.
Mocked up what the installed scoop will look like. I’d like to do some bodywork to the scoop to make it smoother/prettier.
On the backside you can see the hole I cute for scoop installation as well as the ring from the backside.
And the mocked up scoop.
I’ll be adding some kind of mesh to keep stuff out of the duct. It isn’t going to be piped to my intake, it’s just going to dump air into the large area I have allocated for the “airbox”.
First step was making a ring for the opening out of 3/16” steel rod.
Once the ring was complete, I used that as a template for marking the opening in the fender and then cut it out and trimmed it.
Lots of MIG tacks and grinding and it was welded to the fender.
Mocked up what the installed scoop will look like. I’d like to do some bodywork to the scoop to make it smoother/prettier.
On the backside you can see the hole I cute for scoop installation as well as the ring from the backside.
And the mocked up scoop.
I’ll be adding some kind of mesh to keep stuff out of the duct. It isn’t going to be piped to my intake, it’s just going to dump air into the large area I have allocated for the “airbox”.
Might look into some of that windshield glue in a caulk tube and clamp it till it sets.. it's some really strong stuff... Lot of rod shops use it...
n8in8or
I never met a project I didn’t like
Ok, I’ll look into it. We use VHB tape at work to permanently install the lenses to our light cartridges and it’s also really strong stuff. You have to damage the lens to remove it from the aluminum casting.
This stuff comes in a caulk tube, easy to place but hard to remove and you can squish it out like mashing a valve cover down .. I think the right stuff would work also...
And I like what you're doing, I might copy it some day...
And I like what you're doing, I might copy it some day...
n8in8or
I never met a project I didn’t like
That stuff could definitely do the trick, I watched them put the windshield in the Escalade last fall. I was thinking I’d have a lot leftover with nothing to use the remainder on. The Great Stuff is a good idea…..that’s something I’d use, and it certainly is tough. And if it doesn’t work, I can always do the VHB later.
I think you should make me one of those rings also for the ideas 
MrMarty51
Well-Known Member
Urethane
n8in8or
I never met a project I didn’t like
I injured my ankle so I haven’t been able to get anything done for a bit, but today I was finally able to get back out to the barn. I got the fender vent sheet metal welded into the driver side fender. I’m happy with how it turned out.
