millsroger
New Member
Is it possible to get at the spring without pulling the entire door panel off???
-
Welcome to The Truck Stop! We see you haven't REGISTERED yet.
Your truck knowledge is missing!
- Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
- We have tons of knowledge here for your diesel truck!
- Post your own topics and reply to existing threads to help others out!
- NO ADS! The site is fully functional and ad free!
Problems registering? Click here to contact us!
Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!
Inside door handle spring broke
- Thread starter millsroger
- Start date
someotherguy
New Member
You can kinda see it if you pop the switch panel bezel off, but doubt you can do much about it. The plastic piece behind the switch bezel which holds the interior handle is pop-riveted to the inner door skin with about a half dozen rivets. Pulling the panel is fairly easy, just expect that you'll probably break a couple of the fasteners.
On the style of interior your 1994 has, you've got the single screw inside the grab handle, gently pry the switch panel bezel off, gently pry all the christmas tree fasteners from around the sides and bottom of the panel, and here's a gotcha - if it's not already broken, there's a hidden screw at the forward portion of the grab handle - on a tab which is in a black plastic portion. Very easy to overlook but often broken anyway. At this point you can lift the panel up and off the door edge and fish the switch panel through the hole in it, no need to disconnect any of the switches. Helps a huge amount lifting the panel off the door if you have the window down.
Then you get to drill those pop rivets out and have fun playing with the clips that hold the handle and lock linkage rods on.
A set of small picks helps.
Richard
On the style of interior your 1994 has, you've got the single screw inside the grab handle, gently pry the switch panel bezel off, gently pry all the christmas tree fasteners from around the sides and bottom of the panel, and here's a gotcha - if it's not already broken, there's a hidden screw at the forward portion of the grab handle - on a tab which is in a black plastic portion. Very easy to overlook but often broken anyway. At this point you can lift the panel up and off the door edge and fish the switch panel through the hole in it, no need to disconnect any of the switches. Helps a huge amount lifting the panel off the door if you have the window down.
Then you get to drill those pop rivets out and have fun playing with the clips that hold the handle and lock linkage rods on.
A set of small picks helps.Richard
millsroger
New Member
Was afraid of that. Thanks for the tip on the 'hidden screw', will look for it. Sounds like I need to visit the help baggie rack. So, the switch bezel just jiggle wiggles thru the opening? Any suggestions on where to start popping the tree pins out? How flimsy are the clips that hold the pins.
someotherguy
New Member
I usually start popping the trees at the rear lower corner as there's one right in the corner; that lets you squeeze a finger behind the panel and "feel" for where the rest are so you can try to get the tool right on them instead of to the side where you're more likely to accidentally snap them out of the panel. They twist into slotted holes in the panel - some into MDF and some into plastic. It should be noted the large plastic piece facing the mounting area of the side mirror is plastic-welded to the inside panel and also has a christmas tree fastener behind it.
And yeah, once you have the switch bezel popped loose (use the door panel on it too, just take care) it can easily be fenagled through its corresponding hole in the panel as you remove the panel; no biggie at all. If you choose to replace the handle assembly you'll need to disconnect the window and lock switches which is a little bit of a pain. You might take a quick d-cam pic of the layout of the switches and also the wiring on them before disassembly. It's a little tricky getting the switches disconnected.
Richard
And yeah, once you have the switch bezel popped loose (use the door panel on it too, just take care) it can easily be fenagled through its corresponding hole in the panel as you remove the panel; no biggie at all. If you choose to replace the handle assembly you'll need to disconnect the window and lock switches which is a little bit of a pain. You might take a quick d-cam pic of the layout of the switches and also the wiring on them before disassembly. It's a little tricky getting the switches disconnected.
Richard
millsroger
New Member
Thanks for the tips Richard. Don't ya just love these plastic rigs??? At least mine doesn't have the cracked up foam dash top.