Hey man: It has been a while. I was wondering if the guys that get together and help repair veh. were still doing that? I lost my other knee to replacement, and need some help putting my water mist on. I have it for almost over year. I just don't trust these mec. around this area. Each time I...
Hey! Good work guys.. As I read the posts, I thought for a while, that I quaified for help.. I fell and broke 5 ribs, and busted my knee, and during my recovery, my neighbor and I were putting my running boards on, and my knee pop out again.. We got the one board on and thats it.. I have been...
snout
Thanks: I will question my transmission guy about it, he seamed pretty much up date on the trans so far, I just don't trust these people, when it comes to doing things right. He knows what I have in my truck, he doesn't believe it does what I said it will do. His son drove it around after...
interior
I have std. blue Sil. w/ buckets in the front, the drivers side is broke, and I haven't found a replacement. The dash is almost trash, bad electrical all around. Heater blower motor bad, and the rest is just run down. Head liner is ok, upper console is ok, back seat for dog is ok...
special
Would you be interested in buying my truck from me, before I put more money into the interior, and new paint, with my tank, and running boards. I will make you a deal. It's all within two years on the mechanical end of the truck.
Your engine
Have you rebuilt your engine yet? If may I suggest you take a look at the difference between the 6.2 and the 6.5. I was impressed enough to go with the 6.2, because I pulled my mic's out of the bag and went to it, there was more meat on the 6.2 after the bore, than the 6.5 before...
sign.
This is all the signature that it would allow me, do you have anymore sug.?? I am still new to the pc and this sight, so I can learn, not a problem.
Does anyone have any experience with Interiors, wheather it yourselfs, or different outfits, around the Tenn. area. I know a couple of places in the Dallas area but that is to far to go. Any suggestions???
Have you seen the shaft and throw out bearing, arn't they bit small, for that size engine and load?
I would be interested in any upgrades, but I am concerned about the money set back. I have checked on the 373 rear end, the split shift gears. I have not found anything in my price range.
Mild Bill
reply
I have 94 3500 chev. with external slave.
My trans is a rebuilt nv 4500, now there have been some upgrades done to the trans., but I can't find the paper work since we moved up here from louisana. I remember the overdrive is a lot stronger, since I can feel comfortable pulling a load...
answer
The shaft is to small, the bearing is small. I have no other idea what you are asking? I have a new GM clutch ass. in the truck now, one in georgia, and the lok is out in the garage. It seems to be working fine, but my question is how long will it last? I can't find anyone in Tenn...
Bio
I would make sure you will have access to a good long lasting source of fry oil.
Here in Tn. you can't get the oil from anyone, not even the guys who are collecting it. I have two 100 gal tanks and one 300 gal tank, my other equip and stainless tanks are still in Louisana, I can't see...
answer
All my info is up there,I think. 6.2 block, the trans and bell housing are all rebuilt for heavyduty, the truck is 94 1 ton dually 6.5 with about 260 to 280 hp. The rear end I rebuilt with timkin bearings, and the engine was done by diesel depot in Sanderville Ga.
Yes the bearing has...
I am not sure what you are asking! The throw out bearing is internal. The clutch is internal, I have a 5 sp manuel trans. The intire clutch w/bearing and pressure plate.
I am having the work done since I am not able.
MILD BILL
I tried to explain this earlier but the site kept shuting me down...