• Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

Recent content by Mousie2004

  1. Mousie2004

    Limp Mode Codes P2149,P0202,P0203,P0205, P0208

    Don't have pin test kit one would be nice. I will try the spray bottle tomorrow and continue to peel back the remaining harness.
  2. Mousie2004

    Limp Mode Codes P2149,P0202,P0203,P0205, P0208

    I peeled the wiring harness back from the EDU unit up past the alternator to the driver side engine and could not find any issues. I have ordered new injector connectors for the remaining 6 just hoping maybe it could be one of them and wait for a failure.
  3. Mousie2004

    Limp Mode Codes P2149,P0202,P0203,P0205, P0208

    I'll take any suggestions at this point. I will run the wiring around the alternator and see what I can find. Just crazy that when its runs its just like when it was new. Thanks
  4. Mousie2004

    Limp Mode Codes P2149,P0202,P0203,P0205, P0208

    Need help once again truck is a Chevy 2004.5 LLY 2500 HD 66,000 miles. I had this same problem last year truck would shut down completely and I would have to pump the primer to get to run like it was out of fuel never actually run in a limp mode either run or not. I replaced the fuel hoses, new...
  5. Mousie2004

    Limp Mode Codes P2149-P0202-P0203-P0205- P0208

    Need help once again truck is a Chevy 2004.5 LLY 2500 HD 66,000 miles. I had this same problem last year truck would shut down completely and I would have to pump the primer to get to run like it was out of fuel never actually run in a limp mode either run or not. I replaced the fuel hoses, new...
  6. Mousie2004

    Code P0046

    I have a shop full of tools but no lift.
  7. Mousie2004

    Code P0046

    (My reply yesterday should have said NO more codes) Only 66000 on the motor, I didn't have to pull the motor. Removed both inter fender wells and had a lot of patience, up pipe bolts were tough getting out. About a 8 hour removal and a 8 hour reinstall.
  8. Mousie2004

    Code P0046

    Just giving a shoutout to Tefermanator, I finally pulled the turbo on my Duramax last week (what a job) it was just as you said, veins were stuck and all sooted up unison ring was cracked. I cleaned up the veins and turbo installed a new unison ring and gaskets. Truck is running great and...
  9. Mousie2004

    2004 LLY do you have to do a relearn if you replace the vein position sensor.

    2004 LLY do you have to do a relearn if you replace the vein position sensor.
  10. Mousie2004

    Code P0046

    Thanks,
  11. Mousie2004

    Code P0046

    Ok thanks I can take care of driving it harder and getting more exercise.
  12. Mousie2004

    Code P0046

    I removed the vein position sensor today it had a some build up on it so I cleaned it and replaced code light is off for now is this a good indicator it is a bad sensor. Is there a cleaner you can spray to remove the soot.
  13. Mousie2004

    Code P0046

    2004 Silverado 2500 HD 6.6 LLY 65000 miles. Truck is stock bought new only used to pull a 32 ft camper. Truck runs good, engine light has come on at different times and then would go off and stay off then come back on. now it stays on all the time. I removed the battery terminals pulled the...
  14. Mousie2004

    Fuel problems

    Worked on diesel construction machinery most of my life I never seen anything as strange as a this Duramax I purchased new in 2004. I removed the new filter to check the o rings, I know it was a new assembled unit but you never know and all was ok. The old filter, primer pump and fuel I first...
  15. Mousie2004

    Fuel problems

    I removed the new fuel filter assembly to check the gaskets they look good. Re installed and pumped the primer again the truck cranked and run fine for about 5 minutes then died. I have check engine light on not sure what that is I am going to purchase a OBD2 today and see what code it is. I...
Back
Top