• Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

DieselSlug's latest activity

  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    Ok, its most likely a MM1. I had the complete mechanical cable valved hydraulic version of the MM1 on my '94 Silverado. Is your...
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    Mine does have a bolt on cutting edge. It does have a little wear on it but I've got a good 3/4-inch plus before the wear gets to the...
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    I do, but only in minor situations. Do you run shoes on yours? I run them on mine, but at a setting that keeps the cutting edge about...
  • DieselSlug
    DieselSlug reacted to MrMarty51's post in the thread My 2005 Yukon XL with Like Like.
    I thought that was created when the cutting edges is more to 90* angle to the road surface. Like the cutting edge is too close to being...
  • DieselSlug
    DieselSlug reacted to MrMarty51's post in the thread My 2005 Yukon XL with Like Like.
    Looks mighty fine from over here in eastern Montana.
  • DieselSlug
    DieselSlug replied to the thread 2004 Yukon XL 2500 LBZ.
    Congrats on the family addition!
  • DieselSlug
    DieselSlug reacted to BigDogYJ's post in the thread 2004 Yukon XL 2500 LBZ with Like Like.
    new steering stabilizer installed: new tie rod ends: Using my buddies shop has been a dream. it's a 300 mile round trip from my...
  • DieselSlug
    DieselSlug reacted to BigDogYJ's post in the thread 2004 Yukon XL 2500 LBZ with Like Like.
    Sorry it's been a while. First baby was born back in July so life's been a bit busy since then. Made our trip out to TN and back (not...
  • DieselSlug
    DieselSlug reacted to BigDogYJ's post in the thread 2004 Yukon XL 2500 LBZ with Like Like.
    Thats all for now. I'll update after alignment and coolant change. Then we've got some trips lined up (hence why time to do...
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    Time for adjustment.
    • 20260201_153354.jpg
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    The rear has a cover held on with 3 small screws. Once the screws are removed, swing the cover to the right and you can access both bulb...
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    I had hoped to paint the base plates, but im just not going to have time. More snow slated for Monday, leaving this afternoon only to...
    • 20260201_144053.jpg
  • DieselSlug
    DieselSlug reacted to dbrannon79's post in the thread My 2005 Yukon XL with Like Like.
    use lots of anti-seize I would also dab some hot glue on the small screw heads so that they are sealed from the Philips head rusting...
  • DieselSlug
    DieselSlug replied to the thread My 2005 Yukon XL.
    Nutserts for the win, thanks all for the suggestions. Had to install them technically upside down, but it worked. Had to use 8-32 under...
    • 20260201_105819.jpg
    • 20260201_110711.jpg
    • 20260201_114103.jpg
  • DieselSlug
    DieselSlug reacted to dbrannon79's post in the thread My 2005 Yukon XL with Like Like.
    how thick is the steel back plate? would it be thick enough to run an 8-32 tap through and get enough threads to hold similar to how a...
Show older items
Back
Top