Search results

Truck is a 1995 Tahoe (not in my sign). Heath chip, Suburban no EGR intake, Walbro liftpump, S&B air intake, 4" no muffler exhaust ISSUE: When i make a quick step at the ACC petal,(dont have to floor it) the engine stumble and nearly dies. If releasing it a little, the engine comes back to...

Hi there. Just purchased a MagHytec deep transmission pan, part # 4L80E-A. Instrucion manual says use a deep filter only and the part # for the filter is 24210956 (GM/DELCO) Have any of you tried this combination of filter and pan? Reason for asking is that the recommended filter is exactly...

Hi. Consider to change the transmission fluid to synthetic. Do I have to, or should I, flush the transmission and cooler? Or is it good enough to drain, replace filter and fill it up with synthetic oil? Which should make a close to 50% mix of regular and synthetic fluids. Thanks

Hi. A while back I purchased a tune for my 1997 K2500 pick-up. Engine blew and I've purchased a 1999 Suburban K2500. Is it possible for me to put the tuned ECM from the pick-up into the Suburba?. Issues? In fact I do not understand if not? As far as I know the tune only effect the engine and...

Hi guys. When first assembled Service manual says the main bearings are selective fit. What do you do when you replace main bearings? When explained in the service manual it also seems they mixed different sizes upper and lower halves of bearings in the same bearng , sounds insane to me? Do you...

Hi. Engine in one of my trucks is making a loud "bang". Sounds like a shot bearing, appears intermittenly as, at my knowledge, it should not do if it is a bearing? Sound is like smashing on a piece of heavy metal with a sledghammer? It also seems like it's not running on all cylinders, which...

Hi. Is it going to be a problem swapping the injection pump from a 1995 year into a 1997 year Silverado? Blew the engine in the 1997, donor engine is out of a 1995. If I've to swap the pumps I'll do it before the 1995 engine goes into the 1997. Thanks so far. Norwegiandiesel

Hi there. I need to order a new hose assembly for my A/C. Vehicle is a Tahoe 1995 year. The part I need is the hoses with an aluminium block that bolts to the A/C pump. The pump is a Harrison and sits on the right side of the engine (early location). Can't find OEM parts, from RockAuto it seems...

Hi. What is the better and easier way to remove the pitman arm from the steering box? Seems to be very tight space and I do remember other threads pointing to this job as a PITA. Remove the steering box from the frame and do the job out of the truck? Thanks

Hi. Is the 10,5" freefloating rear end from a K2500 pick up fit in place of the OEM Tahoe rear end? And if yes, possible to swap in the front diff and front suspension from the same truck at the front end? Hubs, driveshafts etc???? Thanks

Hi. Does anybody know if the drivetrain (front diff, hubs, control arms, driveshafts and rear axle) from a K2500 6,5L diesel are going to fit on a 1995-2000 Tahoe? Reason for asking is that I'd like to have the more rugged drivetrain from the Pick up onto a Tahoe, especially the rear full...

Hi. IIRR Heath used copper spray on the head gaskets on his race truck, and roumors says he's using it on a regular basis? Any experiences out there? What happens if the copper finds it ways into oil and water passages? Thanks

Hi. Going to do my head gaskets. .010 thicker and ARP studs. Should I use RTV sealant (like blue Permatex) or should I use Locktite thread sealer like the blue one or aother suitable Locktite?(Lots to choose from) Thanks.

Hi. Blew a head gasket. Going to re-install 010" thicker ones. (6,5L) Anyone willing to provide me parts##? Fel-pro and Reinz please. Thanks a lot in advance.

Hi. I'm collectin parts for a future engine build and a SCAT crank is on the whish list. Anyone able to tell if the crank in the link is a genuine one, or a cheap nock-off? Thanks...

Hi. Need to lift the front suspension a little bit, 2"-3" to make some more space for the wheels. Is going to do the lift by changing the torsion bar keys. How much can I lift without messing up the camber? I know the upper control arms have camber adjustments. Is it neccessary to have the...

Hi guys. For long a Tech2 has been on top of my wishlist. Huge price variations. Are there "fake" ones out there? Made in China or another low cost country? Will the Vetronix "3000091" Tech 1 OBD2 Interface Module upgrade my Tech 1 to what I need it to do on 1996 and newer? If not, what else...

Hi girls:hihi: New to this forum, from Norway. (I'll fill in my sig in a while.) Been around in the "other" forum for a while and been into 6,2L and 6,5L diesels since 1990. Still have a lot to learn. For a while I'd four rigs, a 1989 K3500,a 1997 Tahoe, a 1997 K2500 and a 1995 Suburban. K3500...