Search results

Hey buddy, I got all the same readings as you have. What are you thinking now? Any more tests or are we at switching the Ij or the os? Thanks.

Paveltolz, Nice shot of that filter. It hides on the back side of the injection pump. You need to crawl up on top of your raidiator and look around the back side of the pump. I like pictures also.

Hey, Buddy, thanks for taking the time to check your electrcal system out for me. I will check the other pins out for kohms Tomorrow morning and report back on my findings. Thanks.

Acesneights, I read somewhere that the 94 and 95's have the filter. Someone must have tossed yours out I think.

Sounds good Matuva. I am having touble with my truck stumbling and running rough. Code 18 keeps comming up which looks like I might have a optic sensor going bad. So I took out my filter in hopes it would run better. But it didn't help so I am going to put it back in. But like you, if it...

Just my thoughts on what I plan on doing with my 95 6.5 is I plan on leaving my filter in place and if I have problems I am just going to take it out and see if the problems leaves with the filter. That's just me though. Others have their own opinions on the filter and that is good.

Buddy, that is how I understand it also. If you don't have one that is fine. If you are experiencing fishbite then one might want to put one on. Or if you have one installed and experience fishbiting you might want to take it off to see if the fish bite goes away. For the most part they are...

Yea, I am not sure if it is needed. I have just been doing alot of reading and I think I did read that. I think I read that if you are having fishbite that it could be caused by a bad filter. I also think I read that it is a Radio Noise Eliminator?

Buddy, That is without the filter.

I think I read on Heath's website that he recommended putting in the filter harness.

Okay, I am getting 5v at "A" and "D". But I am getting 496 ohms at those two points. That isn't right is it?

Buddy, it runs good without the o/s plugged in. Other than you have to spin the motor over acouple of times to get it to start. The codes are there though when it isn't plugged in and service engine light is on. It did always run alot better once the service engine light came on. I have a...

Hey Guys, Just got in from testing the burb again. I did put the clear hose on the return. I drove it around until it started acting up again. I then checked the hose for bubbles at idle and in drive as I was pushing on the throttle making the engine run rough. There was no bubbles in the...

Buddy, I searched around for location A and D on the connector. I can't seem to find what pins are what. Can you send me in the right dirction so I know what pins to check for power on the OS? Thanks. I should probably take out that OS filter harness and try running it with that removed...

Buddy, I have been reading about code 18 and yes it looks like the optic sensor. I can't just replace that? It looks like it is the black cap item on the top of the pump? Or is it more internal? I have been putting in 16 ounces of diesel clean in each 42 gallon tank. Also I have been...

Well, Here's what I did now. I took it for a test drive and thought I would stop every once in a while, even though it was running okay, and check for codes. I got no codes for a while. Then it started running bad and I stopped and checked for codes. I got Code 18 (Pump Cam Reference Pulse...

Guys, Before I take it for a test drive I pulled the codes. These are the codes that are showing up now. Code 18 Pump Cam Reference Pulse Error Code 35 Injection Pulse Width Error (Response Time Short) Code 36 Injection Pulse Width Error (Response Time Long) THIS A NEW ONE Code 54 PCM...

Sounds good guys, I will report back later Today on what I find. Thanks all.

Yes, it does seem like a heat soak issue. Like earlier, after it sat for acouple of days, it ran great for about 20 minutes. Then I shut it off and let it set for 1/2 hour or so and it started running rough as soon as I started it up. An injection pump would act like that?

Okay, I tracked down a guy that has a 95 pickup and he had his pmd mounted on the fender wall. He came over and we drove my burb around until it got warm and it started running rough again. We then took his pmd off and put it on my burb. Still ran rough. So we eliminated the pmd. I...