Search results

Oh yes, how did I forget Jim. Actually everyone here is a great help. You are at the right place.

I would for sure get the remote mounted pmd out of that location and mount it just behind or under the center of the bumper. You could be doing the pmd more harm now where you have it located rather than leaving on the pump. I would get it out of the engine compartment. I think you said the...

My 92 std cab long box has a 34 gallon tank. My 95 burb has a 42 gallon tank I think. When I ran the the burb down close to empty it sure put a dent in the pocket book when fuel was close to 5 bucks a gallon.

Great find Clipper, I often wonderd where that filter was actually located. I will have to check the condition of mine next time I change the filter. Can one just grab it with a needle nose pliers and pull it up and out?

I don't know if this would tell you anything but I would loosen up the fuel cap and try it again. It probably won't fix the problem but it would be something I would try first. The problem probably is closer to the pump itself. If it is a problem at all. Others should chime in on that one.

Was it a new pmd or a used pmd? Did you leave the ground on the pump or did you bring the ground down to the remoted heatsink? Also on the 94 there is a resistor in the harness next to the optic sensor on the pump. Might want to take that resistor out and see how it runs. Where did you get...

Okay Guys, I just got the transmission put in this evening. A question I should have probably asked before putting in the new clutch. On my old dual mass flywheel I had three pins that were used for putting on the pressure plate. I think they were used for centering the pressure plate? On...

Thanks Josh for the info on there not being a gasket in the rear of the transmission. I also got a seal for the front of the transfercase. Is that very hard to change? Looks like four bolts and the plate should come off alowing me to change the gasket? also I am thinking just snugging up...

Guys, I got my new snout, that the throw out bearing rides on. So, I tipped the tranny on the side to get the bolts out of it. I then looked towards the back end of the tranny and oil was running out of it. Do I need to put a new seal in the back of it? I thought I read somewhere that as...

I am just throwing some ideas out there that might help you. I am having the same type of problems. Mine sounds also like two dry parts meshing together without the oil. But just like yours all my cases are all full of fluid. I can't figure out the problem either. I am going to take all...

Not familiar with the Cooper tires. Have you had your tires balanced lately? If not you might want to have them balanced. I took mine off at home and brought them in two at a time. I went back in the shop and watched them balance them. They were all good but two of them did appear to be...

What brand of tires do you have on? I have a darn vibration on my 02 duramax and when I go on a trip it ruins the whole trip. Darn truck is going to shake apart. If I ever figure out my vibration I will let you know what I find out.

Rear Seal Thanks BK for the response. Good point given in the CDR can. I think it is original with 240,000 miles on it. I got one of ebay a few years back. I will put her on. I don't expect anyone to check these numbers on the cdr but I am hoping that I have the correct one. If they look...

Hey guys before I put the flywheel in and clutch I noticed that the rear seal is alittle bit wet. It doesn't drip but just want you guys to see if I should replace it or just let it be. One mechanic I spoke with said if it isn't very bad don't mess with it. I think some of the oil is coming...

Anyone heard of a Sachs clutch? Or how about a Valeo Clutch? Also what does GM use for their brand clutch?

Okay, I just got off the phone with a large transmission shop. They said that when they build the nv4500 transmission for someone that had converted to the single flywheel they don't usually end up putting in the dampener in the transmission. They said they haven't seen any problems by not...

Okay, I called around on some prices. My connection at GM couldn't get any dual mass flywheels. I talked to a very high volume parts store and they said they can get me the dual mass flywheel for 750 dollars. Dan at Quad 4x4 said the tranny's seem to be lasting longer if you put the dampener...

So Slim Shady, Do you have a parts break down so one can see where this dampener is located? Is it located inside the transmission? One has to take a big nut off the backside of the tranny to install it? I did some calling around to some friends Today and I might have located one. He...

Okay Guys, I just went to the parts store and the cost of a new duel mass flywheel is about 1,000. I guess I will now be leaning towards the single flywheel for around 150 dollars. Does anyone know if I will need to install a dampner that goes on the transmission. From what I understand the...

Thanks for all the great information guys! I have more information and questions. I took the bell housing off and also took the flywheel off. I looked at the speedodometer and I have 240,000 miles on this dual mass flywheel. It was machined down once. I think it is time for a new one. Two...