Search results

I don’t at the moment but it looks like it’s worth the investment

Gotcha I’m using an old snap on scanner so I thought that would give me the data I needed but looks like I’m missing a lot I’ll take a video of all the data it will give me so maybe y’all can see something I’m not. As for the turning of the pump itself it that just tightening the solenoid or is...

Seems like .09 is below the factory setting could that effect the starting?

I see you offset it .53 mine seemed to read .09 is that an acceptable value?

So that’s the thing this engines done decent up until this point being my daily for the last year it’s already had the oil lines replaced fluid damper harmonic balancer got the turbo master for manual boost setup and to clarify I only put about 300 so far so not too happy but not devastated...

I’ll check the value on that tomorrow and see if I can see it engine rpm fluctuates by about 50 rpm’s at idle if that what you mean by wobble

So I didn’t see a inj.sol.close value but the inj close value was 1.5

The Db2 is what I was hoping to find. Just curious on what all would be involved with the computer/control of the transmission.

That’s what I was afraid of from the beginning any suggestions on where to grab a used pump or maybe back to engine swap idea as lowest I’ve found pumps is like 750

So lots of interesting things happened today tried to get it started without the cam sensor plugged in but couldn’t get the rpm’s above 165 bc the batteries were low but did notice it said pcm in vtd fail but the vtd fuel disable was off Not sure if that has anything to do with anything. BUT...

Heard thank you guys again you’ve been a huge help so far

Fuel sample I took also looked a little more on the blue green side rather than a yellow deep straw colored fuel like I can get from shell I know the optical sensor needs straw colored fuel should I run the more straw colored fuel from a separate container?

Ok I see what you’re saying I’ve got the next two days off so I plan on getting a solid charge and running a list of tests done. starting with what seems to be a consensus of the crank sensor test then I’m going to see what the pressure looks like to the pump itself/ try cracking the injectors...

Forgot to add in that I unplugged the crank sensor and it wouldn’t start either already remounted Pmd to a heatsink

So looked at the fuel shutoff at the advice of another forum and it was in working order but noticed the hose next to it, or maybe the shutoff itself if I looked at it wrong, is leaking fuel then found a ton of fuel in the valley from what I could tell there has to be a second leak to cause that...

I’ll try replacing the hose from ffm to ip after work today I tried the optical sensor unplug and it didn’t allow me to start at all. I think it’s just bc I unplugged the op but I got an 0251 code not sure if that’s any different starting problem than what I’m currently fighting but I wouldn’t...

As far as the fuel system goes, I’m getting 6 psi at the t handle when I manually turn on the fuel pump relay with my code reader and when the key is cranking so im assuming the lift pump is good is the t handle pre or post filter? Could something in the filter housing be clogging my fuel after...

So tried the clear hose test and it started with the help of a little wd40 and fluttering the skinny pedal it died within a minute and couldn’t get it started again, but no bubbles in the line. also tried unplugging the optical sensor hoping it was the issue but that didn’t help either. as for...

That’s what I figured might have happened too but I just bought a fresh flight systems from Leroydiesel and it didn’t change the symptoms at all. Are the flight systems known for being duds out of the box? I was planning on relocating to the bumper just wanted to get the truck moving again...

Ill try and keep it short as most will be covered in checklist but basically have a 3500hd that would surge at highway speeds when throttle was released all the way and smoked excessively under load or heavy acceleration. Other than that had no problems aside from an oil leak from oil pan and...