Search results

I'll check it again, but I did pull and check ALL fuses, even those under the hood. Everything appeared shiney and tight. I'll pull the glove box and check the PCM connections in the AM as well. Although if there was a fault there, I may not have voltage to the IP? Last time this similar...

Truck died while idling outside AZ this morning while I was in getting crossover gaskets to fix a leak that developed there yesterday. No start, good crank. Had codes 13, 36, and 68. I've had the 36 and 68, with no overdrive for several weeks now, but truck was running well, with only an...

Havent had overdrive in the 4l80e since early October. Wasnt getting any codes at that point. Now I'm getting a 36 (injection pulse width long) and 68 (trans component slipping). Is the tranny problem likely to cause the dtc 36, or am I looking at two different problems here? Possibly a...

Approx. how much wider is the suzi oil pan vs the 6.5 pan? Looks like the pan will clear ok over the front axle tube. My bigger concern with the 4x4 is how much the adapter offsets the transmission to the rear, and is there is enough clearance behind the core support to move the engine...

I'll be watching with great interest also. Just for clarification, is it the 6bd that is mechanically injected or both the 4bd and 6bd? Also approx costs on the adapters?

TD, cooling stack cleaned in late July in my usual annual maintenance routine.That is...rad pulled cleaned inside and out, system flushed, condenser, oil and steering coolers cleaned til I can see light thru them. Could fan clutch be an issue here? It's only about two years old, no signs of...

Regarding truck in sig below. Tranny running rather hot. 210-230*(sensor in test port on driver side) Coolers run thru rad first, then auxiliary on front of cooling stack, then thru a cooler mounted under the cab with a fan on it. Stock pan and fluid correct on stick. In past couple of...

Before I drove the truck after the spindle cleanup, I put the rear up on jackstands and let 'em spin to give things a bit of "run in" before going around the block. The front CV's werent moving, so I can rule those out....... The noise is definatly coming from the area of the diff. Checked...

Good point. I've been running it unheated on the frame for over two years now, but the coldest it gets here(SW FL) in the winter is about 30-35* for a few hours at night in January. Likely why I havent had any problems. I do like to keep the vehicle ready for all seasons however. So I'll likely...

Was able to clean up the spindle, then had to find a replacement hub as the race had spun inside of it. Put humpty back together again. But now getting an occasional snapping sound from what sounds like the front (pinion/yoke) area of the differential. Anyone ever do a pinion bearing swap on one...

Curious about using the Racor filter as a replacement for the factory FFM. I have the Racor mounted on the frame ahead of the lift pump. While I'm sure that would give sufficient filtering alone, isnt the factory FFM still required for the fuel heater element? Could one just eliminate it...

33990=Cape Coral, FL

33990

Yeah, in SW FL theres only two junkys in town near me, and two more about 40 to 70 miles out (everglades restoration zone put most out of business in last ten years) and shipping on something like that is gonna be pricey also. The seal and inner bearing surface is fine. It's the outer bearing...

for the rear of truck in the signature......bearings, races easy enough to find. Having difficulty locating the repair sleeves. Would like to find one for both, but the one for the outer bearing may be absolutly necessary. Too late to make phone calls tonight, but advance and az are no go...

Forgot to mention, the front bracket is (and always has been) in place.

Sorry for the vagueness. To clarify, it will not start, but makes a loud click at the solenoid. In much the same manner as a discharged battery would make the solenoid click, but not spin the starter. Not hitting the flexplate, but I can get the bendix to spin when I jump the posts on the...

The truck in the sig below has been experiencing random starting problems for the past year or more. It is related only to the starter itself. When the vehicle starts, it runs fine, no codes. I originally thought the crappy remans from AZ were the issue. I was replacing them on the average of...

They appear to be '70-'81 vintage Trans Am fender vents. I looked under the hood, and the factory cutouts inside the fender, right ahead of the hood hinges as mentioned, look like a perfect position for those vents in the pic. Almost like the general designed them for just that purpose. I...

Sorry for the tardy response............. Moog PN....... K6714 Advance $19.95 Rock Auto $14.40 more info...... www.rockauto.com/catalog/moreinfo.php?pk=1023237