Search results

^ do you have to buy the software or just the USB to ALDL cable? I was able to just download the software.

^ My trip odometer doesn't work so I have been going off the odometer keeping my receipts for fuel. So this makes me lazy if I forget to record the mileage. I have had the truck only since November and I am on my 5th tank of gas. Don't drive it much since I am unemployed. Most trips are to...

You can go to the website and they will send you a brochure and a free sample. I am ordering some from a dealer on another website tomorrow. Seams to be reasonably priced. I am currently using Stanadyne performance formula and everyone in a while 2 stroke oil. Not sure if I will be able to...

Wow I found it on Amazon for $190.16.

That is another reason I quit using Silverstars. Its like they run hotter and when installed into a projector beam type of lens, they get to hot and burn out. Haven't had any problems since I switched.

Thanks How about just replacing the whole blower motor resistor. Only like 20 dollars from local auto part store.

Everything tested 0.00 ohms except reading that is shown in red in the picture. Motor does run on the 3 upper speeds, it is just the low speed that doesn't work. Where are the relays you mentioned?

^thanks. Let me go pull it out again and test it. So don't go anywhere. Should be back in ten minutes

^there are springs and resistors. Springs look good just dont know how to test the resistors. I am trying to google how to test them.

^ any suggestions on how to test the resistor pack when it is pulled out.

Okay I went and tested my voltage at the power wire. Wire was purple in color. I had 11.45 volts on low, medium low and high. I had 8.48 volts on medium high. Motor would only spin on the upper 3 speeds and not turn at all on low. So I am not sure if the resistor is bad. Maybe the motor?

^ I too hate those bulbs that the lenses have a blue tint to them. The Cosmo blues are just slightly bluer and the lenses are clear. JiF edit - NSV Link to ebay Japan store (MTECpower) removed. The super whites are just 4250 Kelvins and the the Cosmos are 4750 Kelvins. I will be using super...

Damn, I didn't even think to do that. I should of hooked the multi tester to the power wire and test it. I can at least get to the power wire and test it tomorrow. Also, those 4 relays I talked about earlier may be for the HVAC doors that need to open and close depending on where the air...

When I had the glove box out, up on top all the tubing for the HVAC there was a bracket with what looked like your typical relays. There was 4 of them. The power wire going to the fan looked to be coming from one of these relays. Fan works on all 3 upper speeds and each time you move up a...

^ I use to run the Silver star ultras all the time as well. I like the whiter, brighter light as well. Then before I installed my HID light kit in the 2006 GSXR i bought these: JiF edit - NSV Link to ebay Japan store (MTECpower) removed. I was sold. These are priced really well. Haven't...

I took my fan out to see if I could oil it. It has been making a lot of noise since the cold weather. When I got the fan out the blades were dirty and so was the motor where you could see in the vent tube hole. Blew the motor out, washed the fan blades, oiled the motor and reinstalled. Here...

Well I got my upper plenum hogged out today. It wasn't as dirty as I thought but there is certainly a lot of restriction there. Hogged it out, cleaned it up and went for a test drive. Not sure if there is anymore horsepower, but the turbo spools longer and the noise of the intake system seems...

I clicked on the link and after a few emails from the ebay seller, they told me that they are up and coming and do carry stainless steel kits, crossovers and kits without the muffler as well. May have to contact them via email or phone to get a list of all their items. Real nice to talk too...

I guess I better hurry up and get this done.

^ If the egr has no vacuum to it, can the intake plenums still get dirty with soot? If so then maybe I will have to install the lower F gaskets. Once the top plenum is removed, what is involved with removing the lower?