• Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

Search results

  1. chevytrucksonly

    6.2 casting # with one piece seal

    Trying to get the block cast # for later model 6.2's with piece seal? Thanks
  2. chevytrucksonly

    Haul from Wisconsin area to N. GA

    I need a c/k 3500 single axle hauled from Wisconsin 53502 to N. GA 30528. Let me know your situation. Truck has no engine, Trans or Drive shafts attached - 2000 lb less of load. Will assist loading with equipment and unload also. Schedule for haul in 3-5 weeks or end of month. Pics of truck...
  3. chevytrucksonly

    Haul from Chicago area to N. GA-3500 single axle

    Apx 862 miles - in about 4 weeks To: Albany, WI 53502 to Cleveland, GA 30528 Let me know details. Michael
  4. chevytrucksonly

    Cruise control cable??

    Need cruise cable for 6.2 or 6.5 with mechanical injection pump. Or if anyone could tell me where one can be purchased at a fair price, I would appreciate it.
  5. chevytrucksonly

    AM General/GEP' New 6.5 6500 Optimizer

    250 HP, A 22% INCREASE 550 LB-FT, A 25% Increase OVER 440 LB-FT 210 AMP ALT STD, 400 AMP ALT OPT HIGHER TURBOCHARGER BOOST PRESSURE WITH IMPROVED FLOW OUTLET NEW MOTOR DRIVEN ACTUATOR FOR WASTEGATE CONTROL STRONGER, THICKER CROSS SECTION CONNECTING...
  6. chevytrucksonly

    Fuel Injectors?

    When installing new injectors what is the- ft pound torque 25? I need to check this out, all my manuals say 25. But read today online it was 50 ftps-maybe they confused that with the nozzle Assembly Michael.
  7. chevytrucksonly

    Trans ID Help?

    If you can help me confirm this tranny it would be helpful. The truck I think it came out of is a 90 3500, I ran the VIN and came up with this; MM4 TRANSMISSION,MANUAL 4-SPEED(MERCHANDISING OPTION) 4-SPD MANUAL TRANS PROVISIONS(MM4) M20 TRANSMISSION,MANUAL 4-SPEED(MUNCIE) 4-SPD M/TRANS(M20)...
  8. chevytrucksonly

    Valve cover Bolts?

    Lost note on the placement of where the stud type bolts go. What i remember is that on the bottom side of each V.C toward the front is where the studs go to mount the fuel return line and the fuel injector line bracket for both sides? All top holes use hex bolts and the bottom rear at firewall...
  9. chevytrucksonly

    Valve cover Removal

    Any suggestion on which way to remove and replace covers under the fuel lines (they have been taken loose from brace)? Or is it best to remove lines? Michael
  10. chevytrucksonly

    Copper washer stuck at base of injector hole

    After removing my injectors I noticed that 2 of the copper crush washers were missing. I found them stuck in the injector hole base at the bottom. I have tried ever tool to separate the washer from the base but with no luck. Has anyone experienced this and how did you resolve it? I need to take...
  11. chevytrucksonly

    Firewall and under hood heat and sound insulators?

    The firewall heat/sound insulation is falling apart under the hood. I have found three products, but need to know if anyone has used them and would like your candid opinion. Product Features 1) Thermo-Tec 13575 12" X 24" Adhesive Backed Heat Barrier Aluminized Heat Barrier is made up of...
  12. chevytrucksonly

    To all

    Been around for a while but wanted say hello and thanks to the many that have enlightened me with their wisdom and experience. Can check out my profile for further info about me if desired. MDS
  13. chevytrucksonly

    ? Best After market Turbo

    Based on experience what is your opinion of the best Turbo to purchase, for quality, performance etc? Thank You MDS
  14. chevytrucksonly

    Turbo ? GM-4 to GM-8 change over

    Need some knowledge/experienced based feedback about changing over a GM-4 to a GM-8 on a 1994 6.5; 1) Is there any performance or benefits with going from a GM-4 to a GM-8? 2) It seems physically that the GM-8 has a larger chamber and exhaust neck prior to the downpipe flange? Is there any...
Back
Top