I have a 1975 Ford 3550 backhoe with a cav4 pump.
No start today.
No fuel at the first injector.
No fuel at the injection/ injector line I Took loose at the pump.
I have fuel at the bleeder on the side of the pump.
I read about another bleeder, but haven't found it yet.
I know nothing...
It's been a decade
I bought a. 1998 Toro 223D with a Mitsubishi L3E engine.
Model 30223 Serial # 80205
I think/hope it needs glow plugs. I haven't looked at it yet.
Are there self regulating glow plugs available?
Are either of these numbers self regulating?
GLOW PLUG
Toro Part #...
2016 Ford F-250 Super duty 6.7 Platinum.
Got tires today.
Any opinions on what to buy for parts?
Need brake pads. The rotors look good.
The right lower tie rod end is loose.
Have an oil coated oil pan. What are the likely suspects?
Wife's truck. She's never checked the oil, so I have no...
I have a set here. I believe From Leroy.
I'm not sure which vehicle it was for. So I may need elbows to go to the block on the 1994 K3500.
Somebody somewhere once mentioned elbows that could thread in and had a lock nut or something to keep them pointed the right direction?
Does anybody know...
1994 K3500 NV4500
I wasn't feeling great and had a kid take the starter off the 1994 6.5 diesel.
He was having trouble getting the starter out and took the slave cylinder loose.
I just went to start it for the first time since. The hydraulic clutch pedal is rock hard and will not depress...
I'm looking for some blue & yellow, 5/16 & 3/8 heat shrink ring terminals / eyelets, with the larger Outside diameter rings. 10 or 20 each.
The rings on the terminals I had were about the same size as a washer. 5/16 was probably close to 5/8" diameter
And the 3/8" was probably about 11/16.
I...
What's everyone do to protect their starter wiring from the heat from the downpipe?
The corrugated tubing poking out from under the starter heat shield was a little crusty
I just installed a 3" diamondeye downpipe on the 1994 today.
I noticed the flange that goes to the turbo was considerably smaller outside diameter that the downpipe that was previously on there and smaller than the old OEM that I have in the shed.
Is that going to cause me issues?
It looked...
The wire running to the starter seems fairly heavy.
On a search I found references to a starter relay.
Is this located under the dash?
https://www.rockauto.com/en/catalog/gmc,1994,k3500,6.5l+v8+diesel+turbocharged,1161548,electrical-switch+&+relay,ignition+starter+relay,3804
I have a plugged fuel line on the 1963 John Deere 4010 diesel tractor..
Trying to avoid excess disassembly.
We were able to run a red line for an aerosol can a ways into the line and that worked great as far as it would go.
The steel line is about 3' long and has some tight bends.
We used...
2006 Jeep Liberty CRD Emergency brake dust shield/backing plate.
The left one was all but gone, the right was still there, I had the Jeep at a trusted shop yesterday, because the 1994 had the shop space plugged up.
Neither I, nor the shop, can't find replacement backing plates.
Found these 2...
1994 K3500 6.5 diesel, CC single rear wheels, long bed
We drug the truck across the yard to power wash the engine - hope I didn't do any damage power washing under the hood.
Drug it back and stuck it in the shed.
There was a puddle under the front - my first guess was that I damaged a line...
1994 K3500 crew cab Single rear wheels, NV4500
What is the proper routing and wire size going to the power distribution lugs on the right/passenger firewall on a 1994 K3500?
I pulled the inner fender to investigate a fuel &/or oil leak and replace the starter.
A while back I had a guy...
GM 26000985 Boot,Steering Gear Pitman Shaft
GM 26000985 Boot,Steering Gear Pitman Shaft ; Part Description. BOOT,
Everybody says they don't have one.
Is there an aftermarket number we could give them?