Buy Viagra with Dapoxetine online at our pharmacy. No prescription required. Lowest price guaranteed. Free Worldwide Shipping. Reorders huge Discount.
buy antibiotics online


THIS AD DOES NOT APPEAR TO REGISTERED USERS!
Results 1 to 10 of 10

Thread: 5 and 6 Speed Allison Transmission Specs

  1. #1
    Halt Halt Or I'll Release My Dog RYDNHI4X4's Avatar
    Join Date
    May 2008
    Location
    San Antonio, TX
    Posts
    1,112
    Member #
    2
    Member of CNY Diesel Club



    Default 5 and 6 Speed Allison Transmission Specs

    Here are the clutch apply's for each gear.

    5 speed:

    1st gear: C1 & C5

    2nd gear: C1 & C4

    3rd gear: C1 & C3

    4th gear: C1 & C2

    5th gear: C2 & C3

    6 speed:

    1st gear: C1 & C5

    2nd gear: C1 & C4

    3rd gear: C1 & C3

    4th gear: C1 & C2

    5th gear: C2 & C3

    6th gear: C2 & C4

    Here is what I came up with codes:

    P0218-- Trans Fluid Over Temperature
    P0562-- System Voltage Low
    P0563-- System Voltage High
    P0602-- TCM Not Programmed
    P0606-- TCM Internal Performance
    P0700-- Transmission Control System Malfunction
    P0701-- Transmission Control System Range/Performance
    P0702-- Transmission Control System Electrical
    P0703-- Torque Converter/Brake Switch B Circuit Malfunction
    P0704-- Clutch Switch Input Circuit Malfunction
    P0705-- Transmission Range Sensor Circuit malfunction (PRNDL Input)
    P0706-- Transmission Range Sensor Circuit Range/Performance
    P0707-- Transmission Range Sensor Circuit Low Input
    P0708--Transmission Range Sensor Circuit High Input
    P0709--Transmission Range Sensor Circuit Intermittent
    P0710-- Transmission Fluid Temperature Sensor Circuit Malfunction
    P0711-- Transmission Fluid Temperature Sensor Circuit Range/Performance
    P0712-- Transmission Fluid Temperature Sensor Circuit Low Input
    P0713-- Transmission Fluid Temperature Sensor Circuit High Input
    P0714-- Transmission Fluid Temperature Sensor Circuit Intermittent
    P0715-- Input/Turbine Speed Sensor Circuit Malfunction
    P0716-- Input/Turbine Speed Sensor Circuit Range/Performance
    P0717-- Input/Turbine Speed Sensor Circuit No Signal
    P0718-- Input/Turbine Speed Sensor Circuit Intermittent
    P0719-- Torque Converter/Brake Switch B Circuit Low
    P0720-- Output Speed Sensor Circuit Malfunction
    P0721-- Output Speed Sensor Range/Performance
    P0722-- Output Speed Sensor No Signal
    P0723-- Output Speed Sensor Intermittent
    P0724-- Torque Converter/Brake Switch B Circuit High
    P0725-- Engine Speed input Circuit Malfunction
    P0726-- Engine Speed Input Circuit Range/Performance
    P0727-- Engine Speed Input Circuit No Signal
    P0728-- Engine Speed Input Circuit Intermittent
    P0730-- Incorrect Gear Ratio
    P0731-- Gear 1 Incorrect ratio
    P0732-- Gear 2 Incorrect ratio
    P0733-- Gear 3 Incorrect ratio
    P0734-- Gear 4 Incorrect ratio
    P0735-- Gear 5 Incorrect ratio
    P0736-- Reverse incorrect gear ratio
    P0740-- Torque Converter Clutch Circuit Mal***tion
    P0741-- Torque Converter Clutch Circuit Performance or Stuck Off
    P0742-- Torque Converter Clutch Circuit Stuck On
    P0743-- Torque Converter Clutch Circuit Electrical
    P0744-- Torque Converter Clutch Circuit Intermittent
    P0745-- Pressure Control Solenoid Malfunction
    P0746-- Pressure Control Solenoid Performance or Stuck Off
    P0747-- Pressure Control Solenoid Stuck On
    P0748-- Pressure Control Solenoid Electrical
    P0749-- Pressure Control Solenoid Intermittent
    P0750-- Shift Solenoid A Malfunction
    P0751-- Shift Solenoid A Performance or Stuck Off
    P0752-- Shift Solenoid A Stuck On
    P0753-- Shift Solenoid A Electrical
    P0754-- Shift Solenoid A Intermittent
    P0755-- Shift Solenoid B Malfunction
    P0756-- Shift Solenoid B Performance or Stuck Off
    P0757-- Shift Solenoid B Stuck On
    P0758-- Shift Solenoid B Electrical
    P0759-- Shift Solenoid B Intermittent
    P0760-- Shift Solenoid C Malfunction
    P0761-- Shift Solenoid C Performance or Stuck Off
    P0762-- Shift Solenoid C Stuck On
    P0763-- Shift Solenoid C Electrical
    P0764-- Shift Solenoid C Intermittent
    P0765-- Shift Solenoid D Malfunction
    P0766-- Shift Solenoid D Performance or Stuck Off
    P0767-- Shift Solenoid D Stuck On
    P0768-- Shift Solenoid D Electrical
    P0769-- Shift Solenoid D Intermittent
    P0770-- Shift Solenoid E Malfunction
    P0771-- Shift Solenoid E Performance or Stuck Off
    P0772-- Shift Solenoid E Stuck On
    P0773-- Shift Solenoid E Electrical
    P0774-- Shift Solenoid E Intermittent
    P0778-- Pressure Control Trim Solenoind B Electrical
    P0780-- Shift Malfunction
    P0781-- 1-2 Shift Malfunction
    P0782-- 2-3 Shift Malfunction
    P0783-- 3-4 Shift Malfunction
    P0784-- 4-5 Shift Malfunction
    P0785-- Shift/Timing Solenoid Malfunction
    P0786-- Shift/Timing Solenoid Range/Performance
    P0787-- Shift/Timing Solenoid Low
    P0788-- Shift/Timing Solenoid High
    P0789-- Shift/Timing Solenoid Intermittent
    P0790-- Normal/Performance Switch Circuit Malfunction
    P0801-- Reverse Inhibit Control Circuit Malfunction
    P0803-- 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction
    P0804-- 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction
    P0840-- Transmission Pressure Switch, Solenoid C Circuit
    P0841-- Transmission Pressure Switch, Solenoid C Stuck Open
    P0842-- Transmission Pressure Switch, Solenoid C Stuck Closed
    P0843-- Transmission Pressure Switch, Solenoid C Circuit High
    P0845-- Trans PSI Switch, Solenoid D Circut
    P0846-- Transmission Pressure Switch, Solenoid D Stuck Open
    P0847-- Transmission Pressure Switch, Solenoid D Stuck Closed
    P0848-- Transmission Pressure Switch, Solenoid C Circuit High
    P1688-- Unmanaged Engine Torque Delivered To TCM
    P1709-- Transmission PSI Switch, Solenoid E Circut
    P1710-- Transmission PSI Switch, Solenoid E Circut Stuck Open
    P1711-- Transmission PSI Switch, Solenoid E Circut Stuck Closed
    P1712-- Transmission PSI Switch, Solenoid E Circut High
    P1713-- Transmission PSI Switch, Solenoid Reverse Circut
    P1714-- Transmission PSI Switch, Solenoid Reverse Circut Stuck Open
    P1715-- Transmission PSI Switch, Solenoid Reverse Circut Stuck Closed
    P1716-- Transmission PSI Switch, Solenoid Reverse Circut High
    P1720-- Trim Solenoid "A" Controlled Clutch Not Engaged
    P1721-- Trim Solenoid "B" Controlled Clutch Not Engaged
    P1723-- Trim Solenoid "A" Controlled Clutch Not Engaged
    P1724-- Trim Solenoid "B" Controlled Clutch Not Engaged
    P1726-- Shift Solenoid "D" Controlled Clutch Not Engaged
    P1727-- Shift Solenoid "E" Controlled Clutch Not Engaged
    P1760-- TCM Supply Voltage
    P1835-- Kickdown Circut
    P1860-- TCC (PWM) Solenoid Circut-Electrical
    P1891-- Throttle Pos Sensor Clutch PWM Sig Low Input
    P1892-- Throttle Pos Sensor Clutch PWM Sig High Input
    U1016-- Class 2 Powertrain Controller State of Health
    U1300-- Serial Data Comm Link Low (Class 2)
    U1301-- Serial Data Comm Link High (Class 2)
    U2104-- CAN Bus Reset Counter Overrun
    U2105-- CAN Bus Error ECM[/left]

    Here are some specs I found:


    DETENT SPRING TO VALVE BODY, M6 X 1.0 X 12 (2 REQUIRED) 12 N.m, (9 ft.lb.).

    MAIN VALVE BODY TO SHIFT VALVE BODY, M6 X 1.0 X 50 (23 REQUIRED) 12 N.m, (9 ft.lb.).

    VALVE BODY ASSEMBLY TO CASE, M6 X 1.0 X 50 (15 REQUIRED) 12 N.m, (9 ft.lb.).

    MAIN VALVE BODY TO SHIFT VALVE BODY, M6 X 1.0 X 65 (1 REQUIRED) 12 N.m, (9 ft.lb.).

    SPEED SENSOR RETAINING BOLT, M6 X 1.0 X 13 (3 REQUIRED) 12 N.m, (9 ft.lb.).

    NSBU SWITCH TO MAIN CASE, M8 X 1.25 X 15 (2 REQUIRED) 27 N.m, (20 ft.lb.).

    BOTTOM PAN TO MAIN CASE, M8 X 1.25 X 20 (12 REQUIRED) 27 N.m, (20 ft.lb.).

    BOTTOM PAN DRAIN PLUG 35 N.m, (26 ft.lb.).

    MANUAL SHAFT NUT (INTERNAL & EXTERNAL) 23 N.m, (17 ft.lb.).

    COOLER MANIFOLD TO BELL HSG, M8 X 1.25 X 30 (8 REQUIRED) 30 N.m, (22 ft.lb.).

    COOLER MANIFOLD TO BELL HSG, M8 X 1.25 X 40 (4 REQUIRED) 30 N.m, (22 ft.lb.).

    PUMP COVER TO PUMP BODY, M8 X 1.25 X 55 (5 REQUIRED) 27 N.m, (20 ft.lb.).

    PTO COVER TO MAIN CASE, M10 X 1.5 X 20 COATED (12 REQUIRED) 56 N.m, (41 ft.lb.).

    EXTENSION HOUSING TO MAIN CASE, M10 X 1.5 X 40 (16 REQUIRED) 50 N.m, (37 ft.lb.).

    BELL HOUSING TO PUMP COVER WITH "O" RING, M10 X 1.5 X 50 (10 REQUIRED) 43 N.m, (32 ft.lb.).

    BELL HOUSING TO MAIN CASE, M10 X 1.5 X 50 (15 REQUIRED) 50 N.m, (37 ft.lb.).

    BELL HOUSING TO MAIN CASE, M10 X 1.5 X 70 (5 REQUIRED) 50 N.m, (37 ft.lb.).

    REAR YOKE NUT WHEN USED 123 N.m, (91 ft.lb.).

    TRANSMISSION TO ENGINE 50 N.m, (37 ft.lb.).

    TRANSFER CASE TO TRANSMISSION 50 N.m, (37 ft.lb.).

    TRANSMISSION MOUNT TO ADAPTER HOUSING 47 N.m, (35 ft.lb.).

    TRANSMISSION MOUNT NUTS 40 N.m, (30 ft.lb.).

    Some other info about Solenoids:

    Trim Sol A is Normaly Closed and allows for Limp home in Power Failure Mode
    Trim Sol B is Normaly Open

    Trim Solonoids control Ongoing, Offgoing, and Holding Psi to the 5 clutch packs.

    Solenoids C,D,E are Shift Solenoids (Normaly Closed)

    Shift Solenoids are used to provide logic to distribute fluid to the Clutch Packs

    Solenoid F is a Lockup Solenoid (Normaly Closed)

    Solenoid F controls the Converter Lockup using Pulse Width Modulation (PWM).
    Last edited by RYDNHI4X4; 05-05-2008 at 12:17 AM.

    Steve

    SILENT STEPS
    Silent steps fall gently beside me
    Over the mountain pass
    And through desert sand
    A world away from all that I know
    These steps safely guide me
    And lead me onward home
    Past devices designed to destroy me
    And alerting me to those who mean harm
    These steps walk into danger
    Risking all for me and my land
    No reward is ever requested
    Save for a gentle touch
    and a place to walk beside me
    Pitter pat pitter pat
    These silent steps walk ever on.


  2. #2
    awaiting your return...signed... your friends Diesel Dually's Avatar
    Join Date
    May 2008
    Location
    Mile High
    Posts
    506
    Member #
    3


    Default

    How about anything >= Edge Level 3 and be prepared to look for a replacement!
    Chris
    Box 55-8087 9/11/01 Rest easy brothers, we will take it from here! IAFF L4116
    Stay low and let it blow!

    '02 Chebby CCLB 3500 D/A LS 4x4:

    MySpace Page

    Click HERE to use the Search Feature.

    Click HERE to let me know how angry you are

  3. #3
    Huh? Cougar281's Avatar
    Join Date
    May 2008
    Location
    St Charles, MO
    Posts
    207
    Member #
    6


    Default

    Quote Originally Posted by RYDNHI4X4 View Post
    [B]
    Anyone know what 6th gear uses?
    6th Gear is C2 & C4

  4. #4
    Deputy dmaxx3500's Avatar
    Join Date
    May 2008
    Location
    chicago,
    Posts
    3,171
    Member #
    37


    Default

    so if we lock c2 to c5 do we get 7speeds?
    2008 lmm 3500 ext dually lt,greystone and ebony leather, duramax allison,factory sunroof ,011' bumper and grille

  5. #5

    Default

    Quote Originally Posted by dmaxx3500 View Post
    so if we lock c2 to c5 do we get 7speeds?
    no you get a tie up.

  6. #6
    Agent Quack Smacker MGlickLBZ's Avatar
    Join Date
    May 2008
    Location
    South Central, WI
    Posts
    234
    Member #
    91


    Default

    Quote Originally Posted by Diesel Dually View Post
    How about anything >= Edge Level 3 and be prepared to look for a replacement!
    I would concur unless you like living on borrowed time.

  7. #7
    Member Advocate Pepperidge's Avatar
    Join Date
    Feb 2008
    Location
    Slidell, La
    Posts
    12,323
    Member #
    9



    Default

    Quote Originally Posted by MGlickLBZ View Post
    I would concur unless you like living on borrowed time.

    I've been towing 7500#'s on level 3 and 4...sometimes 5 for going on three years now...

    only limped it once on level 5...This is one tough transmission...
    Pepperidge
    "Democracy is two wolves and a lamb deciding what to have for dinner. Liberty is a well-armed lamb."
    -Benjamin Franklin

    '01 GMC CC SB 4x4 D/A
    "Club 12 Crew Cab"
    Tuned with EFI Live by theFermanator
    HTT66 Turbo, Carillo Rods, Cut & Coated Pistons, Screw in injector cups, 40% over injectors, 42% over CP3, Suncoast Stage V, AirDogII 165
    , StewartEMP Electric Water Pump, AEM Brute Force Intake, ProFab Cast Flows and up pipes, 4" MBRP Exhaust w/CORSA muffler, Sulastics Shackles, Mag Hytec Diff and Trans Pan, Correctrack Spacers, TTT Mirrors, 265/70/17E Hankook DynaPro ATM's, Dakota Digital Gauges,
    "Dura-Sump" Fuel pickup by Dura-Ration
    Member # 3 A(ACLU)
















  8. #8
    McLovin stacks04's Avatar
    Join Date
    May 2008
    Location
    terryville ct
    Posts
    3,587
    Member #
    295
    Member of CT Smoke Club



    Default

    pepp you are one of the lucky ones.
    GOD PLEASE HELP THE USA.
    Those that make peaceful revolution impossible, make violent revolution inevitable.


    Oh Lord, I would live my life in freedom, peace and happiness, enjoying the simple pleasures of hearth and home. I would die an old, old man in my own bed, After a life of enjoying your blessings.
    But if that is not to be, Lord, if monsters should find their way to this corner of the world on my watch, then help me to sweep those bastards from the ramparts, because doing that is good, and right, and just.
    And if in this I should fall, let me be found atop a pile of brass, behind the wall I made of their corpses.

  9. #9
    Just a speck on the wall Philbilly2's Avatar
    Join Date
    May 2008
    Location
    Sandwich, IL ( that is south of Rt. 30)
    Posts
    179
    Member #
    138
    Member of Illinios Diesel Power



    Default

    I must have the golden horseshoe then. I ran Edge on Level 5 stacked with preadator on 65hp for years, yeah it limped quite a bit, but once it learned, she held
    Phil-

    2003 Duramax/Allison
    It's Bone Stock... I Swear

    Team Twisted

  10. #10
    YOU BOYS LIKE MEX-I-CO?!?! DmaxHawk's Avatar
    Join Date
    May 2008
    Location
    The 575
    Posts
    96
    Member #
    413


    Default

    Quote Originally Posted by stacks04 View Post
    pepp you are one of the lucky ones.
    Not so sure, ran mine on PPE 6 (350HP) for thousands of miles before I got the Extreme. I tried to limp it to see how much it could take. Ran that tranny HARD, high boost launches, WOT through 3-4 shift with defuel at 15% and not a single limp. I agree its one tough tranny. Seems like when one is trying to break it, it wont. But when one is afraid of breaking it, it does.

    Maybe we got the good Allys and all you other guys got the lemons:p

    Clutches were completely destroyed by the way...
    Silverado Classic 2500HD LBZ LT3
    ATS Extreme Transmission, ATS 5-Star Converter, ATS Co-Pilot, ATS Deep Pan, ATS Rear Diff. Cover,ATS Sleeves, ATS Front Pipe, ATS Billet Flexplate, PPE Dual Fueler CP3, Fass 150 GPH lift pump, Labonte Motor Sports DIS-S3 Stage 3 Water/Meth Injection Sulastics, Bilstein 5100s on all corners, Air Lift Load Lifter 5000 Helper bags with Wireless control, Cognito Pitman/Idler Braces, AHO Mod, PPE Airbox Mod, Donaldson , EGR Blocked, PCV Rerouted, Plugged Resonator, ISSOPRO Gagues on A-pillar, PPE Hot+2/EFI Live Tuned by me, MBRP 4", BFG 315s on H2s, M&H Slicks. "TJ Loungers", Best time: 13.84@95 (Excluding dual CP3, Fass 150, and Meth)
    "Stomp on the Right Peddle Club" Member #22

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •