1. Welcome to The Truck Stop! We see you haven't REGISTERED yet.

    Your truck knowledge is missing!
    • Registration is FREE , all we need is your birthday and email. (We don't share ANY data with ANYONE)
    • We have tons of knowledge here for your diesel truck!
    • Post your own topics and reply to existing threads to help others out!
    • NO ADS! The site is fully functional and ad free!
    CLICK HERE TO REGISTER!

    Problems registering? Click here to contact us!

    Already registered, but need a PASSWORD RESET? CLICK HERE TO RESET YOUR PASSWORD!

Recent Activity

Activity stream for all registered members at The Truck Stop.

  1. Husker6.5 liked sctrailrider's post in the thread Looks like i have a problem.

    No, the lower comp doesn't hurt anything, it helps everything, what does it take to make power... air & fuel.. the more you have of each...

    Mar 29, 2017 at 2:10 AM
  2. Husker6.5 liked sctrailrider's post in the thread Looks like i have a problem.

    I've said it before a rebuild will cost as much or more than a new crate motor does.. I know it's not the budget most have but it's a...

    Mar 29, 2017 at 2:09 AM
  3. Husker6.5 liked sctrailrider's post in the thread Looks like i have a problem.

    I have seen all the different heads out there, the best are the p400 heads, I have cut them apart and shown the differences, yea they...

    Mar 29, 2017 at 2:09 AM
  4. Husker6.5 liked sctrailrider's post in the thread Looks like i have a problem.

    The Kennedy pistons are a very good design and he now offers them again, the same shop that is machining them will be machining mine for...

    Mar 29, 2017 at 2:08 AM
  5. Husker6.5 replied to the thread Where did that carnage thread go lol.

    And an Optimizer block at that?

    Mar 29, 2017 at 1:57 AM
  6. Husker6.5 liked Will L.'s post in the thread Where did that carnage thread go lol.

    I agree on the above. Love your builds, and can't hold anything against a decision of aftermarket components, but since I have 2 pennys...

    Mar 29, 2017 at 1:56 AM
  7. Husker6.5 liked WarWagon's post in the thread Where did that carnage thread go lol.

    I am only suggesting an odd known case of later failures from hydrolock not that you experienced the same day failure. I merely suggest...

    7_3PSD.jpg Mar 29, 2017 at 1:55 AM
  8. Will L. replied to the thread Where did that carnage thread go lol.

    That sucks. Anything salvageable from it?

    Mar 28, 2017 at 11:31 PM
  9. 6.5L replied to the thread Where did that carnage thread go lol.

    Meaningless at this point, block got flux'd. It's toast. Looks like I am heading back to the 599. Who knows. Got a lot of decisions to make

    Mar 28, 2017 at 10:25 PM
  10. Pepperidge liked BIGR's post in the thread Drove a L5P today.

    Yea, the hood scoop should be good for about 30 extra horses, RIGHT...:)

    Mar 28, 2017 at 9:41 PM
  11. jrsavoie liked Will L.'s post in the thread New Billet crankshaft pulley.

    Ok guys, got mine in today along with a time keeper timing gear set. Good news- NOT PINK! haha. I compared it to the new GEP pulley I...

    Mar 28, 2017 at 9:09 PM
  12. jrsavoie liked Burning oil's post in the thread New Billet crankshaft pulley.

    Thanks again Will. Remember the "special" ends April 1st. If you buy both Billet crank pulley and Fluid Damper I take $20 off.

    Mar 28, 2017 at 9:09 PM
  13. THEFERMANATOR replied to the thread White smoke at start up.....

    All 6.5 heads seem to have cracks between the 2 valves, it's other cracks that are cause for concern. I thought my heads were good until...

    Mar 28, 2017 at 9:09 PM
  14. 1994ch replied to the thread White smoke at start up.....

    Dover Cylinder Head does some pretty amazing work... not sure if they would be able to weld up one that is this bad but I plan on...

    Mar 28, 2017 at 8:47 PM
Loading...